Barnes 200

Talk about your 450b reloading experience, ask questions, etc...

Moderator: MudBug

Forum rules
Please try and keep it safe!

This information is the responsibility of the community, not the forum. 450bushmaster.net is not responsible if you blow yourselves up.

Barnes 200

Postby teddy_d » Sat Jun 16, 2018 5:26 pm

Fired 5 rounds of the barnes 200 grain hollow point, 40 grains of lil gun, OAL 2.210, taper crimp 0.476", 2300 fps, ssub 2" group at 75 yards using a soft case as a rest on a plastic table, 3x32 nikon bdc compact. Inspected each round to note if crimp help after previous shot fired, no movement noted.

Time to load another 5 rounds with 41 grains of lil gun, might adjust the crimp to 0.475/4" if possible. It will be interesting to get this to a higer fps and test trajectory out at 250 yards...?

Hoping these will be the hunting rounds for deer this year.
teddy_d
 
Posts: 67
Joined: Fri Feb 09, 2018 6:34 am

Re: Barnes 200

Postby Bmt85 » Sat Jun 16, 2018 7:22 pm

If I remember correctly, the 200xpb needs 1800fps to start to open. So even if you got it up to 2500fps at the muzzle, you will only get expansion out to about 150yds. If you want expansion to 250yd, you could switch to the 275 TSX. It would need a muzzle velocity of about 2000fps, which is easy enough.
Bmt85
 
Posts: 701
Joined: Wed May 18, 2016 11:13 am
Location: S.E. Michigan

Re: Barnes 200

Postby Hoot » Sat Jun 16, 2018 9:45 pm

teddy_d wrote:Fired 5 rounds of the barnes 200 grain hollow point, 40 grains of lil gun, OAL 2.210, taper crimp 0.476", 2300 fps, ssub 2" group at 75 yards using a soft case as a rest on a plastic table, 3x32 nikon bdc compact. Inspected each round to note if crimp help after previous shot fired, no movement noted.

Time to load another 5 rounds with 41 grains of lil gun, might adjust the crimp to 0.475/4" if possible. It will be interesting to get this to a higer fps and test trajectory out at 250 yards...?

Hoping these will be the hunting rounds for deer this year.


If I'm not too late, I'd advise sticking with the 40gr and taper crimp down into the groove a little further, to yield a diameter measured as close to the mouth as possible, of .474 inch. It'll still headspace with diameter to spare. If your chronographed velocity goes up, without the group size suffering, you might be able to stop there. Measure each round's casehead diameter right at the web before and immediately after each shot as soon as it cools, to watch for pressure signs. You can incur some excessive pressure without the primers showing much flattening at all. If the post shot casehead has increased .001, your knocking on the door of excessive pressure. At a growth of .0015, you're in the door. Beyond that, you're heading for a firearm failure, not to mention some really short case life. Keep your barrel from getting too hot and don't let the loaded rounds sit in the chamber too long, where they soak up heat and increase the volatility of the powder. At least try to keep all of them in there the same amount of time. Ball powers are sensitive to heat. Doing some pre and post shot casehead measurements, helps the time pass while the barrel has some time to cool. Its been ferociously hot lately. Keeping the action open and the mag out helps the barrel cool quicker if its hot where you are shooting.

Hoot
In Theory, there is no difference between theory and practice. In Practice, there is.
User avatar
Hoot
 
Posts: 5083
Joined: Tue Feb 09, 2010 9:34 am
Location: Minnesota

Re: Barnes 200

Postby teddy_d » Sun Jun 17, 2018 9:33 am

Hoot

Basically did what you recommended this morning. 5 rounds with 41 grains yieled 2430fps, sub 2" group.

Magic round?!
teddy_d
 
Posts: 67
Joined: Fri Feb 09, 2018 6:34 am

Re: Barnes 200

Postby teddy_d » Sun Jun 17, 2018 4:25 pm

Hoot

We'll back off to 40 grains and check everything again.
If this is close in fps we'll stick to that weight of powder.

Then start shooting at distances out to 258yds as that is the maximum distance for a clear shot on the farm. Pretty confident this bulllet will kill a deer with a well placed shot, even if it is not going to have maximum expansion.

Thanks for all the information! :ugeek:
teddy_d
 
Posts: 67
Joined: Fri Feb 09, 2018 6:34 am

Re: Barnes 200

Postby ScottyPotty » Fri Sep 21, 2018 6:19 am

Any update on this combo? I just bought some 200gn XPB to give them a try.
ScottyPotty
 
Posts: 43
Joined: Fri Jan 20, 2017 11:42 am


Return to Reloading for the 450b

Who is online

Users browsing this forum: No registered users and 25 guests