I have started casting some 450 boolits

Talk about your 450b reloading experience, ask questions, etc...

Moderator: MudBug

Forum rules
Please try and keep it safe!

This information is the responsibility of the community, not the forum. 450bushmaster.net is not responsible if you blow yourselves up.

Re: I have started casting some 450 boolits

Postby cwlongshot » Fri May 18, 2018 7:44 am

Real happy with powder coat results last night!!

Took three tries to get it! Temp was WAY OFF! Getting powder right... getting knack for positioning bullets...

Third time I had temp to 385 and they came out NICE! Three more small batches and all of last four where as good as I am gonna get.

LEE push thru did A fine job too. (After) even installing gas checks on the 300’s!!

Im on the road till mid next week so better post then. Here was last two bullets completed ready to load.

Image


CW
Last edited by cwlongshot on Tue May 22, 2018 9:03 am, edited 2 times in total.
cwlongshot
 
Posts: 193
Joined: Tue Apr 24, 2018 11:48 am
Location: New England

Re: I have started casting some 450 boolits

Postby cwlongshot » Mon May 21, 2018 7:12 pm

Image

Image

Image

Image

30g IMR4227 sent these into nice tight groups!

Real happy with how well these are shooting.

CW
Last edited by cwlongshot on Tue May 22, 2018 9:02 am, edited 1 time in total.
cwlongshot
 
Posts: 193
Joined: Tue Apr 24, 2018 11:48 am
Location: New England

Re: I have started casting some 450 boolits

Postby Al in Mi » Tue May 22, 2018 3:48 am

nice.

you gonna throttle them up any??
User avatar
Al in Mi
 
Posts: 1982
Joined: Sat Jun 20, 2009 8:24 am

Re: I have started casting some 450 boolits

Postby cwlongshot » Tue May 22, 2018 6:03 am

Al in Mi wrote:nice.

you gonna throttle them up any??

I did not chrony them, but it was a staring load. You can see they "fell" a little form POA with jacketed. But fine for my needs...

Top properly answer you, probably. :) BUT they shoot pretty well and as I am making a load that's more economical, might also make it a lil easier on the shoulder so can enjoy monger. :)

CW
cwlongshot
 
Posts: 193
Joined: Tue Apr 24, 2018 11:48 am
Location: New England

Re: I have started casting some 450 boolits

Postby plant_one » Tue May 22, 2018 8:33 am

is that the PBTP stuff? that PC turned out realllly nice!
User avatar
plant_one
 
Posts: 1109
Joined: Sat Mar 19, 2016 8:58 pm
Location: Oakland County, MI

Re: I have started casting some 450 boolits

Postby cwlongshot » Tue May 22, 2018 9:11 am

So I am pretty happy with the plain base bullet. It did well with three loads, 13g Trail boss, 15g of 5744 and 30g of 4227. ALL shot virtually single hole at 50 yards.

Cooking is going well, I am new but all seems good. I have been told my coating is thick... but If I go thinner, it doesn't cover as well and I see many voids. It dosent seem to harm anything, as I size after coating and it dosent come off... I am happy.

Here is some pics I took of the process. No real order.

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

I cast 10# more of the plain base bullet. BTW It weighs in just under 300 as cast, so its likely a 300G bullet with softer alloy.

Image

I'll coat these next weekend. nice and relaxing as I have been doing them On the back porch with a paper or magazine... load shake cook, shake load cook wait... relxing. I also quench them in water again straight outta the oven.

CW
cwlongshot
 
Posts: 193
Joined: Tue Apr 24, 2018 11:48 am
Location: New England

Re: I have started casting some 450 boolits

Postby Pipefitter172 » Tue May 22, 2018 6:30 pm

Two thin coats (shake, bake, shake, bake, then size) should get you better coverage than one thick coat.
Here is a plethora of information from a bunch of guys that have been doing this a loooong time: http://castboolits.gunloads.com/forumdi ... ternatives
Pipefitter172
 
Posts: 10
Joined: Mon Mar 12, 2018 8:42 pm

Re: I have started casting some 450 boolits

Postby plant_one » Wed May 23, 2018 8:14 am

get some wire mesh and build a basket. you dont need to stand them up individually to cook them. save a little time. pour them in, the bb's will fall thru the basket, as will the extra PC powder. just make sure the bb's will fit thru the size of mesh you get. you dont even need to make sure they're not touching or anything.

(pic from the web)

Image
User avatar
plant_one
 
Posts: 1109
Joined: Sat Mar 19, 2016 8:58 pm
Location: Oakland County, MI

Re: I have started casting some 450 boolits

Postby cwlongshot » Sat May 26, 2018 10:34 am

I tried that at first. It left marks i dont want to see. Im sure that they will effect little, but appearance is improtant to me so ill take the effort to stand them up. (For now at least)

If for some reason I need mass quantities, that would likly change.

CW
cwlongshot
 
Posts: 193
Joined: Tue Apr 24, 2018 11:48 am
Location: New England

Previous

Return to Reloading for the 450b

Who is online

Users browsing this forum: No registered users and 28 guests